Types of Warehouse Racking — The UK Installer's Guide
Rackstor UK ·
Choosing the wrong racking system costs more than the steel. It costs you in wasted space, slow pick rates, forklift damage and the expense of pulling it all out and starting again. This guide covers every major type of warehouse racking installed across the UK, written from the installer's side of the job — not a brochure.
Adjustable Pallet Racking (APR)
The most widely installed racking system in UK warehouses. Adjustable pallet racking uses upright frames and horizontal beams that can be repositioned at standard pitch intervals, usually 50mm or 75mm, to accommodate different load heights. Each bay is independently loaded and unloaded from the aisle using a counterbalanced or reach forklift.
APR suits warehouses with a wide range of SKUs where every pallet needs to be directly accessible. It is the default choice for general warehousing, 3PL operations, food and drink distribution, pharmaceutical storage and manufacturing. Load capacities typically range from 800kg to 4,000kg per beam level depending on the frame section, beam size and upright gauge.
Installation requires accurate floor level survey, correct column guard specification based on forklift type, and load notice calculations supplied by the system manufacturer. All installations should comply with SEMA guidance and EN 15512.
For pallet racking supply and installation across the UK, see warehouserackinguk.co.uk.
Narrow Aisle Racking (VNA)
Narrow aisle racking uses the same upright and beam principle as APR but reduces aisle widths from the standard 2.7–3.5m down to 1.6–1.8m, increasing storage density by 40–50% for the same floor area. Very Narrow Aisle (VNA) systems require dedicated turret trucks or order pickers that travel within wire-guided or rail-guided aisles — standard counterbalanced forklifts cannot operate in these aisles.
VNA suits high-volume distribution centres, cold stores where floor area is expensive, and any operation where land value makes density critical. The system demands a flat, level floor — typically FM2 or better — and the investment in specialist handling equipment must be factored into the total cost of ownership.
Drive-In Racking
Drive-in racking eliminates the aisle entirely. Forklifts drive directly into the racking structure on rails, loading and retrieving pallets from the rear of each lane to the front. It operates on a Last In, First Out (LIFO) basis — the last pallet loaded is the first retrieved.
Drive-in suits homogeneous product with low SKU count and high pallet quantities per SKU — bulk ambient food, beverages, building materials, tyres. Storage density is very high, but selectivity is low. Damage rates to racking are higher than APR because forklifts operate inside the structure, so heavy-duty column guards and regular inspection are essential.
For emergency repairs to drive-in racking, see rackingrepairs.com.
Push-Back Racking
Push-back racking loads from one aisle face only, using nested carts on inclined rails. When a new pallet is loaded, it pushes the existing pallets back along the rail. When a pallet is removed, the remaining pallets roll forward under gravity. Push-back systems typically hold 2–6 pallets deep per lane and operate on LIFO.
Push-back suits operations that need better density than APR but more selectivity than drive-in. It is common in food manufacturing, cold store and retail distribution where multiple pallets of the same SKU are always in stock. No specialist forklift is required — standard reach trucks operate the system.
Pallet Flow Racking
Pallet flow racking uses inclined roller or wheel lanes. Pallets are loaded at the high end and flow forward under gravity to the pick face at the low end. It operates on First In, First Out (FIFO) — the first pallet loaded is the first retrieved — making it the system of choice for products with a short shelf life or rotation requirement.
Pallet flow suits fresh food, pharmaceuticals, beverages and any FIFO-critical operation. Lane depths of 10 to 20 pallets are common. The system demands consistent pallet quality — damaged or non-standard pallets cause lane blockages. Braking rollers and lane separators are essential for safe operation.
Cantilever Racking
Cantilever racking has no front column, giving unobstructed horizontal access along the full length of each arm. It is designed for long, awkward or irregular loads — timber, steel sections, pipes, sheet materials, carpet rolls, aluminium extrusions, glass and boat storage.
Arms are adjustable in height and available in light, medium and heavy duty ratings. Single-sided cantilever runs against a wall; double-sided allows access from both aisles. Load capacities range from a few hundred kilograms per arm on light duty to several tonnes on heavy structural systems.
For cantilever racking supply and installation, see cantileverrackinguk.co.uk.
Mobile Racking
Mobile racking mounts standard APR bays onto motorised bases that travel on floor-fixed rails. The entire racking block compacts together when not in use, with only one or two working aisles open at any time. This can double storage capacity compared to static APR in the same floor area.
Mobile racking is most common in archive storage, pharmaceutical cold stores, evidence storage and high-value goods where security and density both matter. The system requires a structural floor survey and power supply to each base unit. Access control and anti-crush safety systems are mandatory.
For mobile shelving supply and installation, see mobile-shelving.uk.
Mezzanine Floors
A mezzanine floor is a structural intermediate level installed within an existing building, effectively doubling the usable floor area without extending the building footprint. Mezzanines can be built above racking, used as office space, picking levels or additional storage and are typically supported on steel columns with open mesh or solid decking.
Planning permission is not normally required for a mezzanine as a temporary structure, but building regulations approval is required for fire protection, structural design and means of escape. Load capacities are determined by structural calculation.
For mezzanine floor design and installation, see mezzify.co.uk.
Multi-Tier Racking
Multi-tier racking creates multiple full-height picking levels within a single structure, accessed by stairs and walkways integrated into the racking itself. Unlike a mezzanine, multi-tier is a self-supporting racking structure rather than a building element. It is used for small parts, components, picked items and archive storage where high density hand-picking is needed.
Double Deep Racking
Double deep racking positions two APR bays back to back, accessed from one aisle using a double-deep reach truck with a pantograph attachment. Storage density increases significantly compared to single-deep APR, but selectivity is reduced — the front pallet must be removed to access the rear pallet in each lane.
Double deep suits operations with two or more pallets of each SKU and a willingness to manage the additional handling step. It is a cost-effective way to increase density without moving to drive-in or push-back.
Longspan Shelving
Longspan shelving bridges the gap between pallet racking and standard warehouse shelving. It uses the same structural frame principle as APR but with particle board, steel or wire mesh decking and without a pallet truck requirement. It suits hand-loaded items, bulky goods, tyres, engine parts, trade counter stock and retail back-of-house storage.
Bays are typically 2.4m to 4.5m wide with adjustable shelf levels. It can be combined with mezzanine floors to create multi-level hand-pick areas.
Tyre Racking
Tyre racking is a specialist system designed to store automotive tyres safely and efficiently. Tyres present a specific storage challenge — they are heavy, difficult to stack safely in bulk, awkward to handle and present a significant fire risk. Tyre racking holds each tyre or set in a designated position, allowing stock rotation and clear identification.
Systems range from simple longspan-based tyre arms to dedicated heavy-duty tyre racking for high-volume motor factors, fleet operators, tyre fitters and automotive distribution.
Racking Safety, Inspection and Repair
Whatever system is installed, every racking installation is work equipment under PUWER 1998 and must be inspected by a competent person at appropriate intervals. SEMA recommends a minimum of one expert inspection per year, carried out by a SEMA Approved Racking Inspector (SARI).
For a full explanation of the legal framework, inspection intervals and what a SEMA inspection covers, read our SEMA racking inspection guide.
For professional racking inspections across the UK, see racksafetyinspections.co.uk.
For emergency racking repairs, see rackingrepairs.com.
Plan Your Warehouse Layout
Use our free warehouse designer tool to map out your racking layout before committing to a system. Open the Warehouse Designer →
Frequently Asked Questions
What is the most common type of warehouse racking in the UK?
Adjustable pallet racking (APR) is the most widely installed system in UK warehouses. It offers direct access to every pallet, suits a wide range of products and load sizes, and can be reconfigured as operations change.
What type of racking gives the highest storage density?
Drive-in racking and mobile racking offer the highest storage density. Drive-in eliminates aisles entirely; mobile racking compacts multiple bays into a single working aisle. Both involve trade-offs in selectivity and cost.
What is the difference between APR and VNA racking?
Both use upright frames and beams, but VNA (Very Narrow Aisle) reduces aisle widths to around 1.6–1.8m using specialist guided forklifts, increasing storage density by 40–50% compared to standard wide-aisle APR.
What racking is used for long loads like timber or steel?
Cantilever racking is designed for long, awkward or irregular loads. It has no front upright, giving unobstructed horizontal access to full-length arms that hold timber, pipe, sheet material, steel sections and similar products.
How often does warehouse racking need to be inspected?
SEMA guidance recommends a minimum of one expert inspection per year by a SEMA Approved Racking Inspector (SARI), with more frequent inspections in high-risk environments. All racking is work equipment under PUWER 1998 and must be maintained in a safe condition.
Can racking be moved to a new warehouse?
Yes. Most steel racking systems can be dismantled, transported and reinstalled, provided components are undamaged and the new site conditions are suitable. See rackrelocation.co.uk for racking relocation services.
What is the difference between new and used racking?
New racking carries manufacturer certification and known load ratings. Used racking can offer significant cost savings but must be inspected before installation to verify structural integrity and confirm compatibility of components. See rackstorusedracking.co.uk for inspected used racking.